1.1 This specification covers a group of requirements which, with the exceptions of 5.3 and Sections6, 7, 18, 19, 20, 21, 22, 23, and 24, are mandatory requirements to the following ASTM tubular product specifications: Title of SpecificationASTM Designation |
Electric-Resistance-Welded Carbon Steel and Carbon Manganese Steel Boiler TubesA 178/A 178M Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser TubesA 179/A 179M Seamless Carbon Steel Boiler Tubes for High-Pressure ServiceA 192/A 192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A 210/A 210M Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesA 214/A 214M Seamless and Electric-Welded Low-Alloy Steel Tubes A 423/A 423M Seamless Cold-Drawn Carbon Steel Feedwater Heater TubesA 556/A 556M Seamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System ServiceA 822/A 822M These designations refer to the latest issue of the respective specifications.
1.2 One or more of Sections , , , , , , , , , and apply when the product specification or purchase order has a requirement for the test or analysis described by these sections. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation (SI) of the product specification is specified in the order. |
D3951-18(2023) | Standard Practice for Commercial Packaging |
E92-23 | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
A1047/A1047M-05(2023) | Standard Test Method for Pneumatic Leak Testing of Tubing |
A214/A214M-25 | Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes |
A210/A210M-26 | Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes |
A192/A192M-24 | Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service |
A179/A179M-24 | Standard Specification for Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes |
A178/A178M-25 | Standard Specification for Electric-Resistance-Welded Carbon Steel and Carbon-Manganese Steel Boiler and Superheater Tubes |
A530/A530M-18 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe |
A498-06 | Standard Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins |
A423/A423M-19(2026) | Standard Specification for Seamless and Electric-Welded Low-Alloy Steel Tubes |
Fed. Std. No. 183 | Continuous Identification Marking of Iron and Steel Products Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098. |
E570-25 | Standard Practice for Flux Leakage Examination of Ferromagnetic Steel Tubular Products |
E426-16(2021) | Standard Practice for Electromagnetic (Eddy Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys |
A941-26a | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys (Includes all amendments and changes 4/15/2026). |
A822/A822M-20 | Standard Specification for Seamless Cold-Drawn Carbon Steel Tubing for Hydraulic System Service |
A751-25 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
A700-14(2019) | Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
A556/A556M-26 | Standard Specification for Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes |
A370-26 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
E309-24 | Standard Practice for Eddy Current Examination of Steel Tubular Products |
E273-25 | Standard Practice for Ultrasonic Testing of the Weld Zone of Welded Pipe and Tubing |
E213-22 | Standard Practice for Ultrasonic Testing of Metal Pipe and Tubing |
A1058-19 | Standard Test Methods for Mechanical Testing of Steel Products´Metric |
|