1.1 This specification covers the general requirements for steel sheet in coils and cut lengths. It applies to the following specifications that describe carbon steel, structural steel, and high-strength, low-alloy steel (HSLA) furnished as hot-rolled sheet and cold-rolled sheet: Specifications A 414/A 414M, A 424, A 606, A 659/A 659M, A 794, A 1008/A 1008M, and A 1011/A 1011M. 1.2 This specification is not applicable to hot-rolled heavy-thickness carbon sheet coils (Specification A 635/A 635M). 1.3 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.4 For the purposes of determining conformance with this and the appropriate product specification referenced in , values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E 29. 1.5 lists permissible variations in dimensions and mass (see Note 0) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to is mandatory when the "M" specification is used. The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass. 1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units. |
E29-22 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
E11-24 | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
A1073/A1073M-21 | Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet |
A1039/A1039M-25 | Standard Specification for Steel, Sheet, Hot Rolled, Carbon, Commercial, Structural, and High-Strength Low-Alloy, and Ultra-High-Strength, Produced by Twin-Roll Casting Process |
E59-93 | Practice for Sampling Steel and Iron for Determination of Chemical Composition (Withdrawn 1996) |
E290-22 | Standard Test Methods for Bend Testing of Material for Ductility |
MIL-STD-129 | |
Fed. Std. No. 123 | Marking for Shipments (Civil Agencies) |
A606-04 | Standard Specification for Steel, Sheet and Strip, High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, with Improved Atmospheric Corrosion Resistance |
A635/A635M-25a | Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for (Includes all amendments and changes 12/5/2025). |
A1030/A1030M-21 | Standard Practice for Measuring Flatness Characteristics of Steel Sheet Products |
A1008/A1008M-26 | Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable |
A751-25 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
A941-26a | Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys (Includes all amendments and changes 4/15/2026). |
A794-06 | Standard Specification for Commercial Steel (CS), Sheet, Carbon (0.16 % Maximum to 0.25 % Maximum), Cold-Rolled |
A370-26 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
A424-06 | Standard Specification for Steel, Sheet, for Porcelain Enameling |
A414/A414M-25a | Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels (Includes all amendments and changes 12/5/2025). |
A1011/A1011M-25 | Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High-Strength |
A659/A659M-25 | Standard Specification for Commercial Steel (CS), Sheet and Strip, Carbon (0.16 Maximum to 0.25 Maximum Percent), Hot-Rolled |
A700-14(2019) | Standard Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment |
|