ASTM B359/B359M-02 - 10.10.2002
 
1. Scope

1.1 This specification establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer.

1.2 UnitsThe values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

1.3 The tubes are typically used in surface condensers, evaporators, and heat exchangers.

1.4 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information.

Copper or Copper Alloy UNS No.Type of Metal
C10100Oxygen-free electronic
C10200Oxygen-free without residual deoxidants
C10300Oxygen-free, extra low phosphorus
C10800Oxygen-free, low phosphorus
C12000DLP Phosphorized, low residual phosphorus (See Note 1)
C12200DHP, Phosphorized, high residual phosphorus (See NOTE 1)
C14200DPA Phosphorized arsenical (See NOTE 1)
C19200Phosphorized, 1 % iron
C23000Red Brass
C44300Admiralty Metal Types B,
C44400C, and
C44550D
C60800Aluminum Bronze
C68700Aluminum Brass Type B
C7040095-5 Copper-Nickel
C7060090-10 Copper-Nickel
C7062090-10 Copper-Nickel (Modified for Welding)
C7100080-20 Copper-Nickel Type A
C7150070-30 Copper-Nickel
C7152070-30 Copper-Nickel (Modified for Welding)
C72200Copper-Nickel

Note 1—Designations listed in Classification B 224.

1.5 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6 Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification.

 
2. Referenced Documents

B224-16(2022)

Standard Classification of Coppers

B601-24

Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast

B154-16(2022)

Standard Test Method for Mercurous Nitrate Test for Copper Alloys

B153-22

Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing

E2575-19

Standard Test Method for Determination of Oxygen in Copper and Copper Alloys by Inert Gas Fusion

E478-24

Standard Test Methods for Chemical Analysis of Copper Alloys

E255-23

Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition

E243-24

Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes

E118-89(1996)

Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys

E112-25e1

Standard Test Methods for Determining Average Grain Size (Includes all amendments and changes 9/9/2026).

E62-89(1996)

Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

E53-07

Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry

E29-22

Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E8/E8M-25

Standard Test Methods for Tension Testing of Metallic Materials

E3-26

Standard Guide for Preparation of Metallographic Specimens

D4727/D4727M-22

Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes

B968/B968M-16(2022)

Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube

B900-16(2022)

Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies

B858-06(2024)

Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys

B846-24

Standard Terminology for Copper and Copper Alloys

B170-24

Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes