ASTM B359/B359M-12 - 1.4.2012
 
1. Scope

1.1 This specification establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer.

1.2 Units—The values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

1.3 The tubes are typically used in surface condensers, evaporators, and heat exchangers.

1.4 The product shall be produced of the following coppers or copper alloys, as specified in the ordering information.

Copper or Copper Alloy
UNS No.

Type of Metal

C10100

Oxygen-free electronic

C10200

Oxygen-free without residual deoxidants

C10300

Oxygen-free, extra low phosphorus

C10800

Oxygen-free, low phosphorus

C12000

DLP Phosphorized, low residual phosphorus
(See Note 1)

C12200

DHP, Phosphorized, high residual phosphorus
(See Note 1)

C14200

DPA Phosphorized arsenical
(See Note 1)

C19200

Phosphorized, 1 % iron

C23000

Red Brass

C44300

Admiralty Metal Types B,

C44400

C, and

C44550

D

C60800

Aluminum Bronze

C68700

Aluminum Brass Type B

C70400

95-5 Copper-Nickel

C70600

90-10 Copper-Nickel

C70620

90-10 Copper-Nickel (Modified for Welding)

C71000

80-20 Copper-Nickel Type A

C71500

70-30 Copper-Nickel

C71520

70-30 Copper-Nickel (Modified for Welding)

C72200

Copper-Nickel

Note 1—Designations listed in Classification B224.

1.5 The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6 Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification.

 
2. Referenced Documents

B224-16(2022)

Standard Classification of Coppers

B601-24

Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast

B154-16(2022)

Standard Test Method for Mercurous Nitrate Test for Copper Alloys

B153-22

Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing

E2575-19

Standard Test Method for Determination of Oxygen in Copper and Copper Alloys by Inert Gas Fusion

E478-24

Standard Test Methods for Chemical Analysis of Copper Alloys

E255-23

Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition

E243-24

Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes

E118-89(1996)

Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys

E112-25e1

Standard Test Methods for Determining Average Grain Size (Includes all amendments and changes 9/9/2026).

E62-89(1996)

Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

E53-07

Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry

E29-22

Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E8/E8M-25

Standard Test Methods for Tension Testing of Metallic Materials

E3-26

Standard Guide for Preparation of Metallographic Specimens

D4727/D4727M-22

Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes

B968/B968M-16(2022)

Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube

B900-16(2022)

Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies

B858-06(2024)

Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys

B846-24

Standard Terminology for Copper and Copper Alloys

B170-24

Standard Specification for Oxygen-Free Electrolytic Copper—Refinery Shapes