ASTM B395/B395M-02 - 10.4.2002
 
1. Scope

1.1 This specification establishes the requirements for condenser, evaporator, and heat exchanger U-bends that are manufactured from seamless copper and copper alloy tube.

1.2 UnitsThe values stated in either inch-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.

1.3 This specification is applicable to product 2 in. [50 mm] or less, inclusive, in diameter.

1.4 The product shall be produced from one of the following coppers or copper alloys, as specified in the ordering information: Designations listed in Classification B 224.

Copper or
Copper AlloyPreviously Used
UNS No.DesignationType of Metal
C10200OFoxygen-free without residual deoxidants
C10300...oxygen-free, extra low phosphorus
C10800...oxygen-free, low phosphorus
C12000DLPphosphorized, low residual phosphorus
C12200DHPphosphorized, high residual phosphorus
C14200DPAphosphorized, arsenical
C19200...phosphorized, 1 % iron
C23000...red brass
C44300Type Badmiralty metal
C44400Type Cadmiralty metal
C44500Type Dadmiralty metal
C60800...aluminum bronze
C68700Type Baluminum brass
C70400...95-5 copper-nickel
C70600...90-10 copper-nickel
C70620...90-10 copper-nickel-(modified for welding)
C71000...80-20 copper-nickel
C71500...70-30 copper-nickel
C71520...70-30 copper-nickel-(modified for welding)
C72200...copper-nickel

1.5 The following pertains only to the test method described in Sections 11 and 15, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

 
2. Referenced Documents

B153-22

Standard Test Method for Expansion (Pin Test) of Copper and Copper-Alloy Pipe and Tubing

E2575-19

Standard Test Method for Determination of Oxygen in Copper and Copper Alloys by Inert Gas Fusion

B224-16(2022)

Standard Classification of Coppers

B601-24

Standard Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast

B846-24

Standard Terminology for Copper and Copper Alloys

B900-16(2022)

Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies

B154-16(2022)

Standard Test Method for Mercurous Nitrate Test for Copper Alloys

B968/B968M-16(2022)

Standard Test Method for Flattening of Copper and Copper-Alloy Pipe and Tube

E29-22

Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E53-07

Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry

E62-89(1996)

Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

E243-24

Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes

E255-23

Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition

E8/E8M-25

Standard Test Methods for Tension Testing of Metallic Materials

E478-24

Standard Test Methods for Chemical Analysis of Copper Alloys

B858-06(2024)

Standard Test Method for Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper Alloys

E3-26

Standard Guide for Preparation of Metallographic Specimens

E112-25e1

Standard Test Methods for Determining Average Grain Size (Includes all amendments and changes 9/9/2026).

ASME Boiler and Pressure Vessel Code

E118-89(1996)

Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys