| empers shown in , and in those standard sizes shown in , as well as in other nonstandard sizes as agreed upon between the purchaser and supplier. Such pipe and tube is intended for use in structural applications such as highway and bridge rails, chain-link fence posts, handrails, sign structures, awning supports, lighting brackets, etc. Structural pipe and tube is not intended for fluid-carrying applications involving pressure.Note 1 For drawn seamless tube used in pressure applications see Specifications B 210 and B 210M, for seamless pipe and seamless extruded tube used in pressure applications see Specifications B 241/B 241M, and for drawn tube and pipe for general purpose applications see Specification B 483/B 483M. 1.2 Alloy and temper designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those of preceded by A9, for example, A96061 for alloy 6061 in accordance with Practice E 527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see . 1.4 UnitsThe values stated in either inch-pound units or SI units are to be regarded separately as standard. SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification. 1.4.1 While this standard is a combined SI and inch-pound standard, standard pipe sizes are not applicable to SI units, therefore non-rationalized SI units (soft conversions) are shown for reader convenience. Rationalized [hard converted] SI units are shown in brackets while non-rationalized (soft converted) SI units are shown in parentheses. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
B918-01 | Standard Practice for Heat Treatment of Wrought Aluminum Alloys |
B807/B807M-20 | Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys |
B666/B666M-20 | Standard Practice for Identification Marking of Aluminum and Magnesium Products |
B557M-15(2023) | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric) |
B557-15(2023) | Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
E1251-25 | Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry |
H35.2(M) | Dimensional Tolerance for Aluminum Mill Products [Metric] |
MIL-STD-129 | Marking for Shipment and Storage Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil. |
Fed. Std. No. 123 | Marking for Shipment (Civil Agencies) |
CEN EN 14242 | Aluminum and Aluminum Alloys, Chemical Analysis, Inductively Coupled Plasma Optical Emission Spectral Analysis Available from European Committee for Standardization (CEN), 36 rue de Stassart, B-1050, Brussels, Belgium, http://www.cenorm.be. |
E716-16(2021)e2 | Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022). |
B483/B483M-21 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications |
B241/B241M-22 | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
B210M-12 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes (Metric) (Withdrawn 2019) |
B660-23 | Standard Practices for Packaging/Packing of Aluminum and Magnesium Products |
E527-23 | Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS) |
E34-11 | Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys |
B210-12 | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes |
E29-22 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
E607-02 | Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere |
B945-21 | Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers |
B881-25a | Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products (Includes all amendments and changes 1/8/2026). |
|