ASTM C1116/C1116M-10

ASTM C1116/C1116M-10 - 1.7.2010

1. Scope

1.1 This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery. It does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser.

1.2 Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.

1.3 This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is under the jurisdiction of ASTM Subcommittee C27.40.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

C666/C666M-26	Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing
C143/C143M-26b	Standard Test Method for Slump of Concrete (Includes all amendments and changes 8/6/2026).
C685/C685M-25a	Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing (Includes all amendments and changes 1/30/2026).
C1077-26a	Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation (Includes all amendments and changes 8/17/2026).
C1140-03	Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels
C1385-C1385M-10	Standard Practice for Sampling Materials for Shotcrete
C1399-07	Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
C1436-13	Standard Specification for Materials for Shotcrete (Withdrawn 2022)
C1480-00	Standard Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete Application
C1550-26	Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)
C1602/C1602M-22	Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
C1604/C1604M-05(2019)	Standard Test Method for Obtaining and Testing Drilled Cores of Shotcrete
C1609/C1609M-24	Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
C1666/C1666M-08(2023)	Standard Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement
D6942-03(2019)	Standard Test Method for Stability of Cellulose Fibers in Alkaline Environments
D7357-07(2026)	Standard Specification for Cellulose Fibers for Fiber-Reinforced Concrete
D7508/D7508M-20	Standard Specification for Polyolefin Chopped Strands for Use in Concrete
211.1	Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http://www.aci-int.org.
211.2	Standard Practice for Selecting Proportions for Structural Lightweight Concrete
506.2	Specification for Materials, Proportioning and Application of Shotcrete
C684-99	Standard Test Method for Making, Accelerated Curing, and Testing Concrete Compression Test Specimens
C387-06	Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
C231-09	Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C192/C192M-26b	Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory (Includes all amendments and changes 10/13/2026).
C173/C173M-26	Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C172-08	Standard Practice for Sampling Freshly Mixed Concrete
C567-05	Standard Test Method for Determining Density of Structural Lightweight Concrete
C150-07	Standard Specification for Portland Cement
A820/A820M-22	Standard Specification for Steel Fibers for Fiber-Reinforced Concrete
C31/C31M-26b	Standard Practice for Making and Curing Concrete Test Specimens in the Field (Includes all amendments and changes 8/27/2026).
C39/C39M-26	Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
C42/C42M-20	Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
C94/C94M-26d	Standard Specification for Ready-Mixed Concrete (Includes all amendments and changes 10/22/2026).
C125-26	Standard Terminology Relating to Concrete and Concrete Aggregates
C138/C138M-24a	Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete (Includes all amendments and changes 8/6/2024).