ASTM C361M-22 - 1.9.2022
 
1. Scope

1.1?This specification covers reinforced concrete pipe intended to be used for the construction of pressure pipelines with low internal hydrostatic heads generally not exceeding 375 kPa.

1.2?This specification is the SI companion to Specification C361. It is compatible in technical content.

Note 1:?Field tests on completed portions of the pipeline are not covered by this specification for the manufacture of the pipe but should be included in specifications for pipe laying.

1.3?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

 
2. Referenced Documents

C618-25a

Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete (Includes all amendments and changes 4/3/2025).

C595/C595M-25

Standard Specification for Blended Hydraulic Cements

C822-21

Standard Terminology Relating to Concrete Pipe and Related Products

C1602/C1602M-22

Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

C1619-23

Standard Specification for Elastomeric Seals for Joining Concrete Structures

D698-12(2021)

Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft3 (600 kN-m/m3))

D4253-16

Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table

D4254-16

Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density (Withdrawn 2025)

ACI Code 318

Standard Building Code Requirements for Reinforced Concrete Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http://www.concrete.org.

A283/A283M-24

Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates

A496-A496M-07

Standard Specification for Steel Wire, Deformed, for Concrete Reinforcement (Withdrawn 2013)

A497/A497M-07:2007/ADJA0185

Adjunct to A185 Steel Welded Wire Reinforcement, Plain, for Concrete and A497 Steel Wire, Deformed, for Concrete Reinforcement

A575-20

Standard Specification for Steel Bars, Carbon, Merchant Quality, M-Grades

A576-25

Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality

A615/A615M-26

Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

A27/A27M-20

Standard Specification for Steel Castings, Carbon, for General Application

A36/A36M-19

Standard Specification for Carbon Structural Steel

A82-A82M-07

Standard Specification for Steel Wire, Plain, for Concrete Reinforcement (Withdrawn 2013)

A185/A185M-07:2007/ADJA0185

Adjunct to A185 Steel Welded Wire Reinforcement, Plain, for Concrete and A497 Steel Wire, Deformed, for Concrete Reinforcement

A1011/A1011M-25

Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High-Strength

C31/C31M-26a

Standard Practice for Making and Curing Concrete Test Specimens in the Field (Includes all amendments and changes 3/3/2026).

C33/C33M-24a

Standard Specification for Concrete Aggregates (Includes all amendments and changes 11/18/2024).

C39/C39M-26

Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

A675/A675M-14(2025)

Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties

A1008/A1008M-26

Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable

C150/C150M-24

Standard Specification for Portland Cement

C260/C260M-24

Standard Specification for Air-Entraining Admixtures for Concrete

C309-25

Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete

C497M-20

Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile (Metric)

AISI-C1012 Available from the American Iron and Steel Institute (AISI), 1140 Connecticut Ave. NW, Suite 705, Washington D.C. 20036, http://www.steel.org.