ASTM C578-13 - 1.11.2013
 
1. Scope

1.1 This specification2 covers the types, physical properties, and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene. Products manufactured to this specification are intended for use as thermal insulation for temperatures from -65 to +165°F (-53.9 to +73.9°C). This specification does not apply to laminated products manufactured with any type of rigid board facer including fiberboard, perlite board, gypsum board, or oriented strand board.

1.1.1 For Type XIII only, this specification covers the physical properties, and dimensions of cellular polystyrene intended for use as thermal insulation for temperatures from −297 to +165°F (−183 to +73.9°C).

1.2 Consult the manufacturer for specific recommendations and properties in cryogenic conditions.

1.2.1 This specification does not cover cryogenic properties except for the k-factors for Type XIII in Appendix X1. For Type XIII in specific cryogenic applications, the manufacturer and purchaser shall agree upon the actual temperature limits and physical property requirements in addition to the k-factors in Appendix X1.

1.3 The use of thermal insulation materials covered by this specification may be regulated by building codes that address fire performance. For some end uses, specifiers should also address the effect of moisture and wind pressure resistance. Guidelines regarding these end use considerations are included in Appendix X1.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

 
2. Referenced Documents

E176-24a

Standard Terminology of Fire Standards (Includes all amendments and changes 12/9/2024).

D1621-16(2023)

Standard Test Method for Compressive Properties of Rigid Cellular Plastics

D1622-26

Standard Test Method for Apparent Density of Rigid Cellular Plastics

D2126-25

Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging

D2863-23e1

Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) (Includes all amendments and changes 8/18/2025).

C165-23

Standard Test Method for Measuring Compressive Properties of Thermal Insulations

C168-25

Standard Terminology Relating to Thermal Insulation

C177-19(2026)

Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus

C203-22

Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation

C272-01

Standard Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions

C303-21

Standard Test Method for Dimensions and Density of Preformed Block and Board–Type Thermal Insulation

C1512-10(2020)

Standard Test Method for Characterizing the Effect of Exposure to Environmental Cycling on Thermal Performance of Insulation Products

D1600-18

Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

E96/E96M-24a

Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials (Includes all amendments and changes 11/20/2024).

E84-26a

Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 4/15/2026).

C1303-09

Standard Test Method for Predicting Long-Term Thermal Resistance of Closed-Cell Foam Insulation

C1363-24

Standard Test Method for Thermal Performance of Building Materials and Envelope Assemblies by Means of a Hot Box Apparatus

C335-05a

Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation

C390-08(2024)

Standard Practice for Sampling and Acceptance of Thermal Insulation Lots

C518-21

Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus

C550-26

Standard Test Method for Measuring Trueness and Squareness of Rigid Block and Board Thermal Insulation

C870-24

Standard Practice for Conditioning of Thermal Insulating Materials

C1045-19(2026)

Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions

C1058-03

Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation

C1114-06(2019)

Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus

CAN/ULC S770

Standard Test Method for the Determination of Long-Term Thermal Resistance of Closed-Cell Thermal Insulating Foams