ASTM C647-08 - 1.8.2008
 
Significance and Use

Each of the properties listed should be considered in selecting materials for specific projects. A list of the selected properties with limiting values assigned will form a part of the product specification.

All of the properties may not be pertinent in any specific situation, and all of the tests outlined may not be required. A condition to any specification must be an evaluation of the proposed use to determine which properties may be required.

Membrane reinforcements are frequently specified and used with mastics and coatings. Service properties of such systems of finishes may be different from the unreinforced finishes; therefore, it is essential to test specimens of the reinforced system.

 
1. Scope

1.1 This guide identifies properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation.

1.2 These properties relate to application and service. Each property is defined, and its significance and suggested test methods are described.

1.3 The properties appear in the following order in this guide.

Paragraph

Application Properties

6

Consistency

6.1

Coverage

6.2

Build

6.3

Wet Flammability

6.4

Toxicity

6.5

Temperature and Humidity Range

6.6

Surface Wetting and Adhesion

6.7

Gap Filling and Bridging

6.8

Sizing and Sealing

6.9

Corrosion or Solvent Attack

6.10

Drying Time and Curing Time

6.11

Shrinkage

6.12

Storage Stability

6.13

Freeze-Thaw Stability

6.14

Service Properties

7

Specimen Preparation

7.1

Outdoor Durability

7.2

Environmental Resistance

7.3

Temperature Limits

7.3.1

Chemicals and Water Resistance

7.3.2

Mold and Mildew Resistance

7.3.3

Surface Flammability

7.4

Water-Vapor Transmission Rate

7.5

Adhesion

7.6

Damage Resistance

7.7

Impact Resistance

7.7.1

Abrasion Resistance

7.7.2

Stress Resistance

7.8

Flexure

7.8.1

Elongation

7.8.2

Color

7.9

Odor

7.10

Other Properties

8

1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

 
2. Referenced Documents

E659-24

Standard Test Method for Autoignition Temperature of Chemicals

G21-15(2021)e1

Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi (Includes all amendments and changes 6/22/2021).

G23-96

Practice for Operating Light-Exposure Apparatus (Carbon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials (Withdrawn 2000)

D638-22

Standard Test Method for Tensile Properties of Plastics

D658-91

Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996)

D747-10

Standard Test Method for Apparent Bending Modulus of Plastics by Means of a Cantilever Beam (Withdrawn 2019)

D790-25

Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

D822-D822M-13

Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings

D3828-16a(2021)

Standard Test Methods for Flash Point by Small Scale Closed Cup Tester (Includes all amendments and changes 7/26/2021).

D4339-01(2018)

Standard Test Method for Determination of the Odor of Adhesives

C419-20(2025)

Standard Practice for Making and Curing Test Specimens of Mastic Thermal Insulation Coatings

C461-23

Standard Test Methods for Mastics and Coatings Used With Thermal Insulation

C488-16(2023)

Standard Test Method for Conducting Exterior Exposure Tests of Finishes for Thermal Insulation

C639-24

Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants

C681-14

Standard Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds

C733-93

Standard Test Method for Volume Shrinkage of Latex Sealants (Withdrawn 2000)

C755-25

Standard Guide for Selection of Water Vapor Retarders for Thermal Insulation

C168-25

Standard Terminology Relating to Thermal Insulation

C792-23

Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants

E84-26a

Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 4/15/2026).

D2243-20

Standard Test Method for Freeze-Thaw Resistance of Water-Borne Coatings

D2354-10(2023)

Standard Test Method for Minimum Film Formation Temperature (MFFT) of Emulsion Vehicles

D1849-95(2019)

Standard Test Method for Package Stability of Paint

D2444-25

Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

D2453-15

Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds

D2485-26

Standard Test Methods for Evaluating Coatings For High Temperature Service

D2507-93(2001)

Standard Terminology of Rheological Properties of Gelled Rocket Propellants (Withdrawn 2003)

D2939-03

Standard Test Methods for Emulsified Bitumens Used as Protective Coatings (Withdrawn 2012)

D3134-15(2024)

Standard Practice for Establishing Color and Gloss Tolerances

D3274-09(2026)

Standard Test Method for Evaluating Degree of Surface Disfigurement of Paint Films by Fungal or Algal Growth, or Soil and Dirt Accumulation

D3361/D3361M-22

Standard Practice for Unfiltered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings

D2196-20(2026)

Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer

D903-98(2025)

Standard Test Method for Peel or Stripping Strength of Adhesive Bonds

D968-25

Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive

D1310-14(2021)

Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus

D1640-03

Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature

D1654-24e1

Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments (Includes all amendments and changes 7/2/2026).

D1729-22

Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials

D1823-24

Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer

D1824-24

Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates

D92-24

Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

D93-26

Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

D36/D36M-14(2020)

Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

D56-22

Standard Test Method for Flash Point by Tag Closed Cup Tester

D529-04

Standard Practice for Enclosed Carbon-Arc Exposures of Bituminous Materials (Withdrawn 2013)

D543-21

Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

D562-10(2023)

Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer

E96/E96M-24a

Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials (Includes all amendments and changes 11/20/2024).

E162-26

Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source