ASTM C685/C685M-10 - 1.2.2010
 
Significance and Use

A1.2.1 These tests and requirements are used to evaluate loading and operating procedures; verify the accuracy of proportioning and indicating systems; and determine if mixing uniformity has been degraded by excessive wear or by accumulations of hardened concrete, or both (Note A1.1).

Note A1.1—The method of loading the batching-mixing unit, proper maintenance, and other factors may have an effect on the ability of the unit to produce uniformly mixed concrete. For this reason, the use of this test method not only measures the efficiency of the mixer, but also the combined effect of the method of loading and operating the unit.

A1.2.2 This annex provides additional procedures and cautions that are necessary in the application of existing test methods and practices when used to determine the uniformity of freshly mixed concrete.

 
1. Scope

1.1 This specification covers concrete made from materials continuously batched by volume, mixed in a continuous mixer, and delivered to the purchaser in a freshly mixed and unhardened state as hereinafter specified. Requirements for quality of concrete shall be either as hereinafter specified or as specified by the purchaser. When the requirements of the purchaser differ from this specification, the purchaser's specification shall govern. This specification does not cover the placement, consolidation, finishing, curing, or protection of the concrete after delivery to the purchaser. Tests and criteria for batching accuracy and mixing efficiency are specified herein.

1.2 The values stated in either SI units, shown in brackets, or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.3 This specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

1.4 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged use. )

A1.1.1 This annex includes test procedures and uniformity requirements for use in the evaluation of concrete produced in conformance with Specification C685/C685M by an individual batching-mixing unit, loaded to rated capacity.

 
2. Referenced Documents

C989/C989M-26

Standard Specification for Slag Cement for Use in Concrete and Mortars

C1017-C1017M-13

Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete

C637-26

Standard Specification for High-Density Aggregates for Concrete

C618-26

Standard Specification for Coal Ash and Raw or Calcined Natural Pozzolan for Use in Concrete

C595/C595M-26

Standard Specification for Blended Hydraulic Cements

C567-05

Standard Test Method for Determining Density of Structural Lightweight Concrete

C494/C494M-24

Standard Specification for Chemical Admixtures for Concrete

C330-05

Standard Specification for Lightweight Aggregates for Structural Concrete

C1157/C1157M-25

Standard Performance Specification for Hydraulic Cement

C1077-26a

Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation (Includes all amendments and changes 8/17/2026).

C1064/C1064M-23

Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

C260-10

Standard Specification for Air-Entraining Admixtures for Concrete

C231-09

Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C173/C173M-26

Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method

C31/C31M-26b

Standard Practice for Making and Curing Concrete Test Specimens in the Field (Includes all amendments and changes 8/27/2026).

C150/C150M-24

Standard Specification for Portland Cement

C143/C143M-26b

Standard Test Method for Slump of Concrete (Includes all amendments and changes 8/6/2026).

C138/C138M-24a

Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete (Includes all amendments and changes 8/6/2024).

C136-06

Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates

C127-25

Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate

C125-26

Standard Terminology Relating to Concrete and Concrete Aggregates

C94/C94M-26d

Standard Specification for Ready-Mixed Concrete (Includes all amendments and changes 10/22/2026).

C33-07

Standard Specification for Concrete Aggregates

C39/C39M-26

Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

C1602/C1602M-22

Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

C1240-20

Standard Specification for Silica Fume Used in Cementitious Mixtures