ASTM C877M-21

ASTM C877M-21 - 15.1.2021

1. Scope

1.1?This specification covers external sealing bands to be used in conjunction with concrete pipe as defined in Terminology C822 and conforming to Specifications C14M, C76M, C412M, C478/C478M, C506M, C507M, C655M, C985M, C1417M, and C1433M.

1.1.1?Type I, Rubber and Mastic Bands.

1.1.2?Type II, Plastic Film and Mesh Reinforced Mastic Bands.

1.1.3?Type III, Chemically Bonded Adhesive Butyl Bands.

1.2?This specification is the metric counterpart of Specification C877.

Note 1:?This specification covers only the design and material of the sealing bands. Sealing bands covered by this specification are adequate, when properly installed, for external hydrostatic pressures up to 90 kPa, (9.14 m) without leakage. The amount of infiltration or exfiltration flow in an installed pipeline is dependent upon many factors other than the sealing bands; allowable quantities and suitable testing of the installed pipeline and system must be covered by other specifications.

1.3?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D3953-15(2022)	Standard Specification for Strapping, Flat Steel and Seals
D3407-78(1994)e1	Standard Test Methods for Joint Sealants, Hot-Poured, for Concrete and Asphalt Pavements (Withdrawn 1996)
D2240-15(2021)	Standard Test Method for Rubber Property—Durometer Hardness
D2202-00(2023)	Standard Test Method for Slump of Sealants
D1963-85(1996)	Standard Test Method for Specific Gravity of Drying Oils, Varnishes, Resins, and Related Materials at 25/25°C (Withdrawn 2004)
D1682-64(1975)e1	Standard Methods of Test for Breaking Load and Elongation of Textile Fabrics (Withdrawn 1992)
D1278-91a(2020)	Standard Test Methods for Rubber from Natural Sources´Chemical Analysis (Includes all amendments and changes 6/26/2020).
D1171-18	Standard Test Method for Rubber Deterioration´Surface Ozone Cracking Outdoors (Triangular Specimens)
D882-18	Standard Test Method for Tensile Properties of Thin Plastic Sheeting
D624-00(2020)	Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D573-04(2019)	Standard Test Method for Rubber´Deterioration in an Air Oven
D570-22	Standard Test Method for Water Absorption of Plastics
D471-16a(2021)	Standard Test Method for Rubber Property—Effect of Liquids (Includes all amendments and changes 6/25/2021).
D412-16(2021)	Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
D395-18	Standard Test Methods for Rubber Property´Compression Set
D217-21a	Standard Test Methods for Cone Penetration of Lubricating Grease (Includes all amendments and changes 12/20/2021).
D36-06	Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
C1417M-19	Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
A167-99	Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip
C1433M-22	Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)
C985M-22	Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric)
C822-21	Standard Terminology Relating to Concrete Pipe and Related Products
C766-84	Test Method for Adhesion After Impact of Preformed Tape Sealants (Withdrawn 1994)
C681-14(2019)	Standard Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds
C507M-22	Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
C506M-22a	Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric) (Includes all amendments and changes 9/29/2022).
C478M-19	Standard Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric) (Withdrawn 2020)
C412M-19	Standard Specification for Concrete Drain Tile (Metric)
C655M-19a	Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) (Includes all amendments and changes 8/5/2019).
C14M-20	Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)
C76M-22a	Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric) (Includes all amendments and changes 9/12/2022).