ASTM E1868-10 - 1.7.2010
 
Significance and Use

This test method is used to estimate the amount of volatile materials present in a material.

This test method is useful for design purposes, service evaluation, regulatory statutes, manufacturing control, quality control, specification acceptance, development, and research.

The results obtained by this test method may be equivalent to those obtained by other test methods and may be known by other terms in their respective fields. Other tests and terms encountered include loss-on-heating (see Footnote and Test Methods D6, D2288, and E359); heating loss (see Test Method D1509); evaporative loss (see Test Method D2595); volatile organic carbon, moisture, or water (see Test Methods D2216 and D3175); volatility (see Test Method D4893); highly volatile matter (see Test Method E897); and volatile content (see Guide D2832).

 
1. Scope

1.1 This test method describes a procedure for determining the amount of volatile matter of any kind that is driven off from a test specimen under a specific set of temperature and time conditions. This test method determines only the mass of material lost, not its identity.

1.2 This test method is applicable to a wide variety of solid or liquid materials, mixtures, or blends where the major component is stable at the test temperature.

Note 1—This test method can be applied to the analysis of volatile organic compounds (VOC) content in metalworking fluids and direct contact lubricants subject to South Coast Air Quality Management District (SCAQMD) Rule 1144.

1.3 The applicable temperature range for this test method is generally between ambient temperature and 1000°C.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5 There is no ISO method equivalent to this test standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

 
2. Referenced Documents

D1509-18(2023)

Standard Test Methods for Carbon Black—Heating Loss

D3175-20

Standard Test Method for Volatile Matter in the Analysis Sample of Coal and Coke

D2832-92(2016)

Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings

D2595-22

Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range

D4017-22

Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method

Rule?1144

Metalworking Fluids and Direct-Contact Lubricants

E2040-19

Standard Test Method for Mass Scale Calibration of Thermogravimetric Analyzers

E1860-23

Standard Test Method for Elapsed Time Calibration of Thermal Analyzers

E1582-21

Standard Test Method for Temperature Calibration of Thermogravimetric Analyzers

E1142-23b

Standard Terminology Relating to Thermophysical Properties (Includes all amendments and changes 10/5/2023).

E897-88(1998)

Standard Test Method for Volatile Matter in the Analysis Sample of Refuse-Derived Fuel

E691-23

Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

E473-23b

Standard Terminology Relating to Thermal Analysis and Rheology (Includes all amendments and changes 10/5/2023).

E359-17

Standard Test Methods for Analysis of Soda Ash (Sodium Carbonate)

E177-20

Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

D4893-20

Standard Test Method for Determination of Pitch Volatility

D2288-97(2001)

Standard Test Method for Weight Loss of Plasticizers on Heating (Withdrawn 2010)

D1475-13(2020)

Standard Test Method for Density of Liquid Coatings, Inks, and Related Products

D2216-19

Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

D6-95(2000)e1

Standard Test Method for Loss on Heating of Oil and Asphaltic Compounds