ASTM F2764-10 - 15.4.2010
 
1. Scope

1.1 This specification covers requirements and test methods for triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1600 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with a interior wall, a exterior wall and an annular corrugated profile middle wall (Fig. 1).

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

 
2. Referenced Documents

F477-14(2021)

Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

A666-23

Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

D256-23e1

Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).

D618-21

Standard Practice for Conditioning Plastics for Testing

D638-22

Standard Test Method for Tensile Properties of Plastics

D790-17

Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

D792-20

Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D1238-23a

Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).

D1505-18

Standard Test Method for Density of Plastics by the Density-Gradient Technique

D1600-18

Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

D2122-22

Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

D2321-20

Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

D2412-21

Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

F2136-18(2024)

Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

LRFD, Section 12

AASHTO LRFD Bridge Design Specifications Section 12 - Buried Structures and Tunnel Liners

Fed. Std. No. 123

Marking for Shipment (Civil Agencies)

MIL-STD-129

Marking for Shipment and Storage

D2444-21

Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

D2990-17

Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

D3212-21

Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

D3895-19

Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry

D4101-24

Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials

D4218-20

Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique

D4389-04

Standard Specification for Finished Glass Fabrics Woven From Rovings

D6992-16(2023)

Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method

F412-23

Standard Terminology Relating to Plastic Piping Systems