ASTM F468M-05a - 1.11.2005
 
1. Scope

1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications.

1.2 Unless otherwise specified, nuts used on these bolts, cap screws, and studs shall conform to the requirements of Specification F 467M. Nuts shall be of the same alloy group as the fastener on which they are used and shall have a specified minimum proof stress equal to or greater than the specified minimum tensile strength stress of the fastener on which they are used.

Note 1—This specification is the metric companion of Specification F 468.

 
2. Referenced Documents

E29-22

Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E53-07

Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry

E38-85

Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys (Withdrawn 1989)

E34-11

Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys

E18-22

Standard Test Methods for Rockwell Hardness of Metallic Materials

E8M-04

Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008)

D3951-18(2023)

Standard Practice for Commercial Packaging

B574-23

Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod and Bar

B565-20

Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods

F606M-14

Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) (Withdrawn 2015)

F1470-24

Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

F467M-06a(2018)

Standard Specification for Nonferrous Nuts for General Use (Metric) (Includes all amendments and changes 9/20/2018).

B211M-12

Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold-Finished Bar, Rod, and Wire (Metric)

B193-20

Standard Test Method for Resistivity of Electrical Conductor Materials

B154-16(2022)

Standard Test Method for Mercurous Nitrate Test for Copper Alloys

E1409-13(2021)

Standard Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion

E478-08(2017)

Standard Test Methods for Chemical Analysis of Copper Alloys

E62-89(1996)

Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)

E354-21e1

Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys (Includes all amendments and changes 2/23/2022).

E227-90(1996)

Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)

E165-09

Standard Practice for Liquid Penetrant Examination for General Industry

E120-00

Standard Test Methods for Chemical Analysis of Titanium and Titanium Alloys (Withdrawn 2003)

E101-91

Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-To-Plane Technique (Withdrawn 1996)

E92-23

Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials

E76-88(1998)

Standard Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)

E54-80(1996)

Standard Test Methods for Chemical Analysis of Special Brasses and Bronzes (Withdrawn 2002)

E55-23

Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

E75-76(1996)

Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys