ASTM F715-07(2012) - 1.5.2012
 
Significance and Use

Membrane materials are subjected to these tests in order to provide data that reasonably relate to membrane response under the actual conditions of spill control barrier or storage device use.

Although these test methods provide data on individual performance of membrane materials, all combinations of actual conditions of spill control barrier or storage device use are not simulated in this sequence of tests.

 
1. Scope

1.1 These test methods cover laboratory-conducted performance tests for coated fabrics used in spill control barriers or in temporary storage devices.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

 
2. Referenced Documents

D2644-12(2018)

Standard Tolerances for Yarns Spun on the Woolen System

D751-19

Standard Test Methods for Coated Fabrics

D3117-03

Standard Test Method for Wax Appearance Point of Distillate Fuels (Withdrawn 2010)

D3884-22

Standard Guide for Abrasion Resistance of Textile Fabrics (Rotary Platform Abrader Method)

G26-96

Practice for Operating Light-Exposure Apparatus (Xenon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials (Withdrawn 2000)

D2500-23

Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels

D2425-23

Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry

D1796-22

Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)

D1319-20a

Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption (Includes all amendments and changes 9/14/2020).

D1298-12b(2017)e1

Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method (Includes all amendments and changes 3/14/2023).

D1266-18

Standard Test Method for Sulfur in Petroleum Products (Lamp Method)

D1149-18

Standard Test Methods for Rubber Deterioration´Cracking in an Ozone Controlled Environment

D975-23a

Standard Specification for Diesel Fuel (Includes all amendments and changes 12/19/2023).

Fed. Std. No. 191A

Textile Test Methods Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, Attn: NPODS.

D129-18

Standard Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) (Withdrawn 2023)

D97-17b(2022)

Standard Test Method for Pour Point of Petroleum Products (Includes all amendments and changes 11/29/2022).

D93-20

Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

D86-23ae1

Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure (Includes all amendments and changes 2/9/2024).

D524-15(2019)

Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products

D482-19

Standard Test Method for Ash from Petroleum Products

D445-23

Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

D287-22

Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer/Method)

D130-19

Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test

D543-21

Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents

D664-18e2

Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration (Includes all amendments and changes 1/4/2019).

D613-24

Standard Test Method for Cetane Number of Diesel Fuel Oil